SOFTWARE     |    INSTRUMENTS    |    SYSTEMS
About  |  Support  |  Contact
» Support » Downloads » InspectionWare Applications
OPG TRUSTIE Acquisition
Download installers for Data Acquisition and Analysis
Support

Overview


    This page contains downloadable Windows installers for OPG TRUSTIE Acquisition software, and supporting documentation.

System Requirements

    OS supported: Windows 10 64 bit or later

    PC with Intel i5 i7 or i9 multi-core processors, and at least 32 GB RAM are recommended. Larger memory capacity may be required for handling large scan files.

    Multiple NIC's with Gigabit bandwidth are strongly recommended. Data streaming during scanning is bandwidth intensive.

    Galil GDK drivers must be pre-installed on the PC in order to connect to the Galil motion controller.

    GDK | Galil Design Kit | Galil



Download and Installation Instructions
    1. Right-click on the file name in the "Downloads" section below and choose "Save Target As" or to download the file.
    2. Locate the file you have just downloaded then Right-Click and select "Run As Administrator" to initiate the installation process
    3. On launch click on the setup button (Gear Icon) to see the settings page, then click on Licensing
    4. Activate the soft license using the Serial Number that was emailed to you.

Release Notes

Version
Date
Notes
0.1 TRUSTIE Acquisition 64
2019-11-14
Initial Release for OPG trials
1.0 RC2 TRUSTIE Data Collection
2021-06-18
User interface and features added per OPG feedback
1.1 B1 TRUSTIE Acquisition
2023-02-15
Interim Release for Kinectrics and OPG testing
1.1 B3 TRUSTIE Acquisition
2023-02-24
Bug fixes for scan file save and add valve indicators
1.1 B4 TRUSTIE Acquisition
2023-03-15
Axial Encoder Change Experimental
1.1 B5 TRUSTIE Acquisition
2023-03-16
Axial Encoder Scaling Experimental
1.1 B6 TRUSTIE Acquisition
2023-03-17
Advanced tab for admin and axial motion/scaling based on drive shaft encoder
1.1 B7 TRUSTIE Acquisition
2023-04-18
Human Factors guidance for GUI implemented
SGMS communications (Modbus) added.
Emergency Stop awareness indicator added
1.1 B8 TRUSTIE Acquisition
2023-04-25
Expose temperature set points, WAGO watchdog support
1.1 B9 TRUSTIE Acquisition
2023-04-26
Update E-Stop conditions
1.1 B10 TRUSTIE Acquisition
2023-05-01
Belt Pressure Equation fix
1.1 B11 TRUSTIE Acquisition
2023-05-03
Pop ups stay on main UI
1.1 B12 TRUSTIE Acquisition
2023-05-12
Test build
1.1 B13 TRUSTIE Acquisition
2023-05-15
Test build
1.1 B14 TRUSTIE Acquisition
2023-05-26
Updated UI per OPG requests, File Saving & prompts improved
1.1 B15 TEST TRUSTIE Acquisition
2023-06-07
Test build with fix for stall detection and C scan update speed, scroll on pixel per point, added A scan window setup options
1.1 B16 TRUSTIE Acquisition
2023-06-08
Fixes for UI controls refresh, pallet position saving on setup file, Estop override option (temporary), updating measure per step
1.1 B17 TRUSTIE Acquisition
2023-06-22
Pause and Continue scanning behaviour, file saving from file menu,removed stop all motors button, frequency check close all tab
1.1 B18 TRUSTIE Acquisition
2023-07-17
Advanced tab visibility, Cal Info update, Scan Info update, Axial to Linear, Circ to Rotary
1.1 B19 TRUSTIE Acquisition
2023-07-18
Bug fix for advanced button not opening in Scan Settings
1.1 B20 TRUSTIE Acquisition
2023-07-24
Bug fix for saving data, linear scan data save
1.1 B21 TRUSTIE Acquisition
2023-07-25
Bug fix for saving sdt and iwdat files
1.1 B22 TRUSTIE Acquisition
2023-07-31
Saving sdt in 8 bit format, LZ4 compression
1.1 B23 TRUSTIE Acquisition
2023-08-03
Default browsing and saving location for setup files
1.1 B23.1 TRUSTIE Acquisition
2023-08-03
Fix for go to table selection
1.1 B24 TRUSTIE Acquisition
2023-08-10
Fix for scan setting save and load, E-Stop data save prompt
1.1 B25 TRUSTIE Acquisition
2023-08-11
Fix for SGMS Status Update and Current Row, Col.
Fix for Gate selection drop-down
1.1 B26 TRUSTIE Acquisition
2023-08-14
Fixed SGMS connection status indicator on Hardware management pop-up panel.
1.1 B27 TRUSTIE Acquisition
2023-08-15
Fixed launch of File Saving prompt pop-up upon E-Stop triggered
1.1 B28 TRUSTIE Acquisition
2023-08-15
File Saving prompt pop-up is executed upon all scan end / exit / abort events
1.1 B29 TRUSTIE Acquisition
2023-11-09
Header & Cal Info editable always,removed filter from instrument adv settings, A Scan length per setup, added rotary goto, encoder readouts and goto settings in adv tab, UI changes per OPG, Cal info option updated with "Not Applicable"
1.1 B30 TRUSTIE Acquisition
2023-11-14
Fixed Goto bug with default setup in advanced tab, cosmetic fix for setup section buttons and motion control in right side control panel,Linear distance check default to false
1.1 R1 TRUSTIE Acquisition
2023-08-17
Initial release.
1.1 R2 TRUSTIE Acquisition
2023-11-16
Readonly header fields for year and operator, default values updated for linear stall detection.
1.1 R2 TEST TRUSTIE Acquisition
2024-02-01
Fixes for issues 92, 130, 156, 159, 160 i.e. winspect sdt compatibility, vessel leg editable, add CLR vessel type, support ID default to CAL, data file save as points to root folder
1.1 R2 HF TEST1.0 TRUSTIE Acquisition
2024-04-04
Fixes for issues 92,94,107,156,157,158,160,163
1.1 R2 HF TEST1.1 TRUSTIE Acquisition
2024-04-08
Fixes for issue 167, HF
1.1 R2 HF TEST1.3 TRUSTIE Acquisition
2024-04-11
HFE updates and refocus of Save Data Pop up window
1.1 R2 HF1 TRUSTIE Acquisition
2024-04-11
Scan information close button fix and motion props defaults when publishing.
Updated User Manual Rev 04
Access to downloads on this page is restricted.
Please provide the following:
( Required field)
E-mail:
Download Password:
The following file links will become active once the required information is submitted:
Related Files
InstallIWTrustieAcquisition-1.1R2 HF1.exe (89.1 MB)
OPG TRUSTIE Acquisition User Manual 1.1 R04.pdf (2 MB)
Document Reference
Categories
NDE Software
InspectionWare 
Document Number
DSEO-BHLSFQ5043
Published
05/03/2023 Rev: 1.0
Support for InspectionWare
  Print Email page Share