Pulser Specifications
Pulser	Pulser Voltage	5 to 200 Volts	5 Volt
	Pulser Rise Time	<5 ns	N/A
	Pulser Width	20 nsec to 500 nsec	2 nsec
	Pulse Repetition Frequency	1 Hz to 20 kHz	1 Hz
	Pulser Delay	0 to 25,000 nsec	1 nsec
Receiver Specifications
Receiver Amplifiers	Gain	-70 dB	0.25 dB
	Input Noise	2 nV typical	N/A
	Gain Linearity	Better than 0.25dB	N/A
	Input Impedance	50 Ω	N/A
	Bandwidth	.75 MHz to 25 MHz (-3 dB)	N/A
	Channel Crosstalk	< 60dB between channels at 2 MHz
Filters	Analog Filters	0.75 MHz to 5 MHz (-3 dB) Bandpass Filter	Discrete selection
		2 MHz to 10 MHz (-3 dB) Bandpass Filter
		5 MHz to 10 MHz (-3 dB) Bandpass Filter
		0.5 MHz to 20 MHz Broadband
Distance Amplitude Correction	DAC Dynamic Range	0 to 40 dB	0.25 dB
	DAC Trigger	Transmit pulse or material interface echo	User selectable
	No of DAC curves	256 utilising up to 64 kbytes
	DAC update	40 dB/µsec
	DAC Clock Rate	0.78 MHz to 25 MHz selectable	6 settings
Digitizer and Digital Processing
Digitizer	ADC Resolution	12 bits	N/A
	ADC Rate	25, 50, and 100 MHz	User selectable
	Element Summing	up to 512 elements	N/A
Rectification	Rectification	No Rectification Fullwave +ve halfwave -ve halfwave	Discrete selection
	Post Rectification Filter	None and 7 selectable settings
Hardware Gates	Gates	4 gates utilizing up to 32 kbytes
	Gate Delay	64 k sample points from trigger or I/F echo
	Interface Echo	Hardware interface trigger for gate and DAC
Digital Processing	Hardware Peak Processing	Up to 80 peaks (N + largest), first peak, largest peak
	Threshold	160 to 4095	1
	Averaging	2 to 256 real-time
	Output Options	Peak processed data or full digitized waveform
	Gain Reduced Firing	Selectable to be triggered on saturation with programmable adjustment level
	GRE	1 element, n elements or summed waveform
General Specifications
Interfaces	Control Interface	100 Base-T Ethernet , Gigabit Ethernet
	Digital Encoders	4 axes of 32 bit inputs accepting 5 Volt encoders at rates of up 700 kHz
	Digital I/O	8 channels. TTL inputs 8 channels Open Collector outputs - sinking up to 400 mA
Connections	UT Connectors	Hypertronics 160-pin. HLMYJPAPF16000 Suitable Mating Connector: Hypertronics HLMMXJCASM16000
	Control Connector	Industrial Ethernet RJ45
	Encoder Connector	30 pin receptacle: LEMO EGG.4B.330.CLM Suitable Mating Connector: LEMO FGG.4B.330.CYCD10Z
	Digital I/O Connector	24-pin receptacle: LEMO ECC.4B.324.CLM Suitable Mating Connector: LEMO FGC.4B.324.CYCD10Z
Physical	Case Size	450 mm x 380 mm x 170 mm
	Power Supply	90 - 260 V AC at 45 - 100 Hz
	Weight	15 kg
Environmental	Enclosure	IP20 (ruggedized enclosure available)
	Temperature	Operating: 0 - 40 °C Storage: -20 to 70 °C
	EMC	EN61326
	Safety	EN61010

The following options can be specified when ordering MicroPulse 5 PA instruments:

Phased Array Channels: 32, 64 and 128 channels are standard. 256 and 512 channel instruments are by special order.

Conventional Channels: Phased Array instruments may be equipped with conventional channels in banks of 16.

Rackmount: for permanent installations, a rackmount chassis is available